| draft-ietf-sigtran-m3ua-mib-04 Description: Request For Comments
You can download source copies of the file as follows:
Listed below is the contents of file draft-ietf-sigtran-m3ua-mib-04.txt.
Network Working Group Antonio Roque
INTERNET-DRAFT Ericsson
Expires in six months August, 2002
SS7 MTP3-User Adaptation Layer (M3UA)
Management Information Base using SMIv2
<draft-ietf-sigtran-m3ua-mib-04.txt>
Status of This Memo
This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC 2026. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas, and
its working groups. Note that other groups may also distributeworking
documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months and
may be updated, replaced, or obsoleted by other documents at any time. It
is inappropriate to use Internet-Drafts as reference material or cite
them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/lid-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This document is an individual submission to the IETF. Comments should be
directed to the authors.
Abstract
The MTP3-User Adaptation Layer is a protocol for the transport of any SS7
MTP3-User signalling (e.g., ISUP and SCCP messages) over IP using the
services of the Stream Control Transmission Protocol. Also, provision is
made for protocol elements that enable a seamless operation of the MTP3-
User peers in the SS7 and IP domains. This protocol would be used between
a Signalling Gateway (SG) and a Media Gateway Controller (MGC) or IP-
resident Database. It is assumed that the SG receives SS7 signalling over
a standard SS7 interface usingthe SS7 Message Transfer Part (MTP) to
provide transport.
This memo defines the Management Information Base (MIB) module which
describes the minimum amount of objects needed to manage the
implementation of the M3UA.
Roque, et al [Page 1]
Internet Draft M3UA MIB using SMIv2 August, 2002
Open Issues
- Remove this section.
- Remove Revision History
- Decide under which object identifier branch of the SNMP tree, M3UA will
be placed (value obtained when submitted to the IETF editor).
- Update references to drafts.
Table of Contents
Status of This Memo.......................................1
1. Introduction..........................................3
1.1 Abbreviations........................................3
2. The SNMP Framework....................................4
3. Structure of the MIB..................................5
3.1 Management...........................................6
3.1.1 Attributes.........................................6
3.1.1.1 Protocol General Variables........................6
3.1.1.2 Protocol General Statistics.......................6
3.1.2 Tables.............................................6
3.1.2.1 Logical Application Table.........................6
3.1.2.2 Logical Application Statistics Table..............7
3.1.2.3 Signaling Process Endpoint Table..................7
3.1.2.4 Signaling Process Endpoint Statistics Table.......8
3.1.2.5 Application-Endpoint Table........................9
3.1.2.6 Routing Table....................................10
3.1.2.7 Network Appearance Table.........................10
3.1.2.8 Expanded Tables..................................11
3.1.2.8.1 Service Indicator Table........................11
3.1.2.8.2 OPC Table......................................11
3.1.2.8.3 CIC Range Table................................11
3.1.2.8.4 Point Code Table...............................12
3.1.2.8.5 Local and Remote IP Address Tables.............12
3.1.2.9 Reverse Lookup Tables............................13
3.2 Conformance.........................................14
3.2.1 Groups.............................................14
3.2.2 Compliance.........................................14
4. Definitions..........................................14
5. References...........................................54
6. Security Consideration................................56
7. Acknowledgments.......................................56
8. Authors' Addresses....................................56
9. Revision History......................................56
9.1 Changes from draft rev 03 to draft rev 04:...........57
9.2 Changes from draft rev 02 to draft rev 03:...........57
9.3 Changes from draft rev 01 to draft rev 02:...........58
9.4 Changes due to the alignment with the RFC2851 update. 58
Roque, et al [Page 2]
Internet Draft M3UA MIB using SMIv2 August, 2002
1. Introduction
This memo defines the Management Information Base (MIB) module which
describes managed objects for implementations of the M3UA.
The document starts with a brief description of the SNMP framework and
continues with the MIB explanation and security consideration among
others.
Terms related to the SCTP architecture are explained in [1]. Other
especific abbreviations are listed below.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
1.1 Abbreviations
AS - Application Server
ASP - Application Server Process
ASPM - Application Server Process Management
CIC - Circuit Identification Code
DPC - Destination Point Code
IPSP - IP Server Process
MIB - Management Information Base
M3UA - SS7 MTP3-User Adaptation Layer
NA - Network Appearance
NI - Network Indicator
OPC - Origination Point Code
PC - Point Code
SCTP - Stream Control Transmision Protocol
SG - Signaling Gateway
SI - Service Indicator
SMI - Structure of Management Information
SNMP - Simple Network Management Protocol
SP - Signaling Process
SSN - Subsystem Number
2. The SNMP Framework
The SNMP Management Framework presently consists of five major
components:
- An overall architecture, described in RFC 2271 [SNMPArch].
Roque, et al [Page 3]
Internet Draft M3UA MIB using SMIv2 August, 2002
- Mechanisms for describing and naming objects and events for the purpose
of management. The first version of this Structure of Management
Information (SMI) is called SMIv1 and described in RFC 1155 [SMIv1], RFC
1212 [SNMPv1MIBDef] and RFC 1215 [SNMPv1Traps]. The second version,
called SMIv2, is described in RFC 1902 [SMIv2], RFC 1903 [SNMPv2TC] and
RFC 1904 [SNMPv2Conf].
- Message protocols for transferring management information. The first
version of the SNMP message protocol is called SNMPv1 and described in
RFC 1157 [SNMPv1]. A second version of the SNMP message protocol, which
is not an Internet standards track protocol, is called SNMPv2c and
described in RFC 1901 [SNMPv2c] and RFC 1906 [SNMPv2TM]. The third
version of the message protocol is called SNMPv3 and described in RFC
1906 [SNMPv2TM], RFC 2272 [SNMPv3MP] and RFC 2574 [SNMPv3USM].
- Protocol operations for accessing management information. The first set
of protocol operations and associated PDU formats is described in RFC
1157 [SNMPv1]. A second set of protocol operations and associated PDU
formats is described in RFC 1905 [SNMPv2PO].
- A set of fundamental applications described in RFC 2273 [SNMPv3App] and
the view-based access control mechanism described in RFC 2575
[SNMPv3VACM].
Managed objects are accessed via a virtual information store, termed the
Management Information Base or MIB. Objects in the MIB are defined using
the mechanisms defined in the SMI. This memo specifies a MIB module that
is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced
through the appropriate translations. The resulting translated MIB must
be semantically equivalent, except where objects or events are omitted
because no translation is possible (use of Counter64). Some machine-
readable information in SMIv2 will be converted into textual descriptions
in SMIv1 during the translation process. However, this loss of machine-
readable information is not considered to change the semantics of the
MIB.
3. Structure of the MIB
The MIB is structured in the following way:
m3uaMib
/ \
m3uaManagement m3uaConformance
/ \ / \
m3uaAttributes m3uaTables m3uaGroups m3uaCompliances
/ \ |
Roque, et al [Page 4]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaConfig m3uaStatistics m3uaCompliance
where the following sections are described :
- m3uaManagement, where all the objects to manage M3UA are defined
under this branch.
- m3uaAttributes, where general attributes values are placed. It is
divided in:
- m3uaConfig, where the general M3UA configuration
parameters are listed.
- m3uaStatistics, where general Statistics for M3UA are listed.
- m3uaTables, where specific attributes for each element that can be
defined and used to manage a M3UA Based System. Every table is
structured in the following way:
m3uaTableName
|
m3uaTabAttributes
/ \
m3uaTabConfig m3uaTabStatistics
Note: Statistics only apply to some of the tables.
These tables hold data for:
Logical Application,
Signaling Process,
Signaling Point Endpoint,
Routing Keys,
Network Appearances,
Point Codes,
Local and Remote IP Address.
- m3uaConformance, for the Unit of Conformance.
- m3uaGroups, M3UA MIB variables have been grouped according to their
funcionality and the context they belong to.
- m3uaCompliances, Minimal list of objects in the M3UA
MIB module that an agent developer must implement.
3.1 Management
3.1.1 Attributes
Roque, et al [Page 5]
Internet Draft M3UA MIB using SMIv2 August, 2002
3.1.1.1 Protocol General Variables
The first section of the MIB contains the general variables of the M3UA
protocol. Maximum, minimum and initial values can be found here.
3.1.1.2 Protocol General Statistics
Statistics included here relate to the whole M3UA layer. Statistics
related to a specific Peer Association are defined inside its concerned
table (context).
3.1.2 Tables
3.1.2.1 Logical Application Table
Defines data related to a Logical Application, its state and traffic
handling mode.
A Logical Application is a logical entity serving an specific Routing
Key.
An AS or SG are Logical Applications as they are the final translation
result for Routing Keys in the Routing Tables at SGPs, ASPs or IPSPs
respectively.
Thus they can be managed using the same object.
LApps managed in a node behaving as an ASP, would represent SGs.
On the contrary, LApps managed in a node that behaves as an SGP, would
represent ASs.
Finally, LApps managed in a node that behaves as an IPSP, would also
represent ASs.
m3uaAppTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppType / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppState / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppTrafficMode / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.2 Logical Application Statistics Table
This table contains statistic information about each Logical Application.
m3uaAppStatTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Roque, et al [Page 6]
Internet Draft M3UA MIB using SMIv2 August, 2002
| m3uaAppUnreachable / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.3 Signaling Process Endpoint Table
Defines data related to a Signaling Process Endpoint.
A SP Endpoint identifies a peer node were a Signaling Process (SGP, ASP
or IPSP) is running.
The table contains the Endpoint identifier and data related to the
association to that endpoint.
This table is expanded with the Remote IP Address Table that identify the
endpoint and with the Local IP Address Table that identify the local node
for that endpoint.
The table contains data related to the SCTP association to that endpoint,
as its state, number of streams, and the Association ID, provided by SCTP
when the association is established.
m3uaSpEpTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocId / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocRemHostName / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocRemPort / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocReqOutStreams / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocOutStreams / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocIncStreams / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocState / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.4 Signaling Process Endpoint Statistics Table
Defines statistics related to a Signaling Process Endpoint.
The table contains statistics data related to the M3UA messaging
exchanged through that association between the Signaling Processes that
hold the association.
m3uaSpEpStatTable
Roque, et al [Page 7]
Internet Draft M3UA MIB using SMIv2 August, 2002
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocId / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDataOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDataRecived / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspupOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspupAckOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspacOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspacAckOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspdnOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspdnAckOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspiaOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspiaAckOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspupIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspupAckIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspacIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspacAckIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspdnIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspdnAckIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspiaIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocAspiaAckIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocNotifyOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocErrorOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocNotifyIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocErrorIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDunaOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Roque, et al [Page 8]
Internet Draft M3UA MIB using SMIv2 August, 2002
| m3uaSpEpAssocDavaOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocSconOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDupuOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDaudOut / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDunaIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDavaIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocSconIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDupuIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpAssocDaudIn / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.5 Application-Endpoint Table
Defines data related to the endpoint where a Signaling Process is
running, and the Logical Application IDs which the SP is serving.
A Signaling Process is a process instance that uses M3UA to communicate
with other signalling process. An ASP, an SGP and an IPSP are all
signalling processes.
As a SP can maintain different states and traffic handling modes for
Every Lapp it is serving, i.e. The ASP_1 may be ASP-ACTIVE(LOAD-SHARING)
for AS_1, ASP-INACTIVE for AS_2 and ASP-ACTIVE(OVER-RIDE) for AS_3.
Then, one entry will be created in this table per every combination of AS
Id and Endpoint Id.
All the entries corresponding to the same SP running in an specific
Endpoint will have a common link, the Endpoint Id.
m3uaAppSpEpTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppSpEpState / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAppSpEpRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.6 Routing Table
Every entry in this table contains the data that defines a Routing Key.
Roque, et al [Page 9]
Internet Draft M3UA MIB using SMIv2 August, 2002
As a Routing Key may be composed of any combination of basic SS7 Routing
elements, if an element is not included in the routing key, a default
value is assigned. This default value can continue being considered as an
indexing value itself.
m3uaRouting
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKDpc / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKNa / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaPeerAppId / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaPeerAppTrafficMOde / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRoutingRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.7 Network Appearance Table
Defines the data specific to a Network Appearance.
m3uaNaTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNA (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNaNI / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNaMtp3ProtocolType / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNaMtp3ProtocolVariant / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNaMtp3ProtocolVersion / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNaRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.8 Expanded Tables
3.1.2.8.1 Service Indicator Table
This table expand information in entries in Routing Table.
A Routing Key can be composed by a list of Service Indicators.
m3uaSi
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKId (index) / ... |
Roque, et al [Page 10]
Internet Draft M3UA MIB using SMIv2 August, 2002
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKSi / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKSiRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.8.2 OPC Table
This table expand information in entries in Routing Table.
A Routing Key can be composed by a list of OPCs.
m3uaOpc
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKOPc / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKOpcRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.8.3 CIC Range Table
This table expand information in entries in Routing Table.
A CIC Range can be defined for some of the OPC's which compose a Routing
Key.
m3uaCicRange
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKOPc (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKCicMin / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKCicMax / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaRKCicRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.8.4 Point Code Table
This table expand information in entries in Network Appearance Table.
A SG with several Network Appearances may be connected to different SS7
Networks and may be represented in each SS7 Network by different Point
Codes.
m3uaNaPcTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNA (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Roque, et al [Page 11]
Internet Draft M3UA MIB using SMIv2 August, 2002
| m3uaNaPC(index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaNaPcRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.8.5 Local and Remote IP Address Tables
These tables expand information for SP Endpoint Tables. When an SP
Endpoint entry is created, a default free Association Id is assigned to
that entry. The Local and Remote IP Address Table that will be used to
establish an association towards the SGP, ASP or IPSP are stored in these
tables.
If the remote addresses change during association negotiation, they will
be updated in the corresponding table.
a) Table for local IP addressess information:
This table stores information related to the local IP address/-es
reserved for the association. It's indexed by the IP address.
b) Table for remote IP addresses information:
This table stores information related to the remote IP address/-es
reserved for the association. It's indexed by the IP address.
"Address" and "AddressType" use the syntax InetAddress and
InetAddressType defined in the Textual Conventions for Internet Network
Address [RFC2851-update].
In the general case this syntax is valid for IPv4, IPv6 and DNS but only
the first two options will be valid for this MIB
The IP addresses that the MIB supports are defined in the [RFC2851]:
global and non-global (either with a zone index or not) IPv4 addresses,
global and non-global (either with a zone index or not) IPv6 addresses.
However, DNS value is not being used to identify an IP address since it
is only valid during initialization (once this stage is finished, both
sides only use IP addresses). To keep the name of the remote peer, an
entry has been created (m3uaAssocRemHostName) in the association table.
When no DNS name is provided by the remote SCTP endpoint at init time,
this value will be NULL. Otherwise, the received DNS name will be stored.
m3uaAssocLocalAddressTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAssocLocalAddressIPType(index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAssocLocalAddressIP (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAssocLocalAddressRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Roque, et al [Page 12]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaAssocRemAddressTable
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaSpEpId (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAssocRemAddressIPType(index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAssocRemAddressIP (index) / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| m3uaAssocRemAddressRowStatus / ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
3.1.2.9 Reverse Lookup Tables
There are four reverse lookup tables to help management applications to
efficiently access conceptual rows in other tables. This is the way for
not performing expensive tree walks through large number of associations.
All of these tables are optional.
The defined reversed lookup tables allow performing a lookup using the
following variables:
- Get Signaling Process Endpoint from Association: Obtains the LOCAL
Identifier of the Endpoint that is connected through the Specified
Association Id.
There is only one Endpoint per Association.
- Get Routing Key from Application: Obtains the LOCAL Routing Key
Identifier of the Routing Key that results in the specified Logical
Application Id.
There is only one RK per Application.
- Get Routing Key from DPC and NA: Obtains the LOCAL Routing Key
Identifier of the Routing Key that contains the specified combination
of DPC and NA.
There is only one RK per DPC and NA combination.
- Get Signaling Process Endpoints serving an Application: Obtains the
LOCAL Identifiers of the Endpoints that are serving the specified
Logical Application Id.
There might be more than one Endpoint per Logical Application.
It is not possible to either create or delete rows in these tables.
3.2 Conformance
3.2.1 Groups
This section includes all the variables defined in the MIB grouped by
function.
3.2.2 Compliance
Requirements of the M3UA MIB to be implemented.
Roque, et al [Page 13]
Internet Draft M3UA MIB using SMIv2 August, 2002
4. Definitions
M3UA-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Unsigned32,
Counter32, Counter64, mib-2
FROM SNMPv2-SMI -- RFC 2578
RowStatus
FROM SNMPv2-TC -- RFC 2579
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF -- RFC 2580
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB -- RFC 2851
;
m3uaMIB MODULE-IDENTITY
LAST-UPDATED "200208060000Z"
ORGANIZATION "IETF SIGTRAN Working Group"
CONTACT-INFO
" Antonio Roque Alvarez
Postal: Ericsson Espana S. A.
C/Ombu 3
28045 Madrid
Spain
Phones: +34 91 339 3523
Emails: Antonio.Roque@ericsson.com"
DESCRIPTION
"The MIB module for managing M3UA implementation."
REVISION "200208060000Z"
DESCRIPTION
"MIB module developed for the SIGTRAN IETF group.
Based on M3UAv11"
::= { mib-2 xxxx } -- IANA needs to choose this value
-- when sent to the RFC editor
-- Top-level structure of the MIB
m3uaManagement OBJECT IDENTIFIER ::= { m3uaMIB 1 }
m3uaConformance OBJECT IDENTIFIER ::= { m3uaMIB 2 }
m3uaAttributes OBJECT IDENTIFIER ::= { m3uaManagement 1 }
m3uaTables OBJECT IDENTIFIER ::= { m3uaManagement 2 }
Roque, et al [Page 14]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaConfig OBJECT IDENTIFIER ::= { m3uaAttributes 1 }
m3uaStatistics OBJECT IDENTIFIER ::= { m3uaAttributes 2 }
m3uaLogApplication OBJECT IDENTIFIER ::= { m3uaTables 1 }
m3uaLAppAttributes OBJECT IDENTIFIER ::= { m3uaLogApplication 1 }
m3uaLAppConfig OBJECT IDENTIFIER ::= { m3uaLAppAttributes 1 }
m3uaLAppStatistics OBJECT IDENTIFIER ::= { m3uaLAppAttributes 2 }
m3uaSpEndPoint OBJECT IDENTIFIER ::= { m3uaTables 2 }
m3uaSpEpAttributes OBJECT IDENTIFIER ::= { m3uaSpEndPoint 1 }
m3uaSpEpConfig OBJECT IDENTIFIER ::= { m3uaSpEpAttributes 1 }
m3uaSpEpStatistics OBJECT IDENTIFIER ::= { m3uaSpEpAttributes 2 }
m3uaAppSpEndPoint OBJECT IDENTIFIER ::= { m3uaTables 3 }
m3uaAppSpEpAttributes OBJECT IDENTIFIER ::= { m3uaAppSpEndPoint 1 }
m3uaAppSpEpConfig OBJECT IDENTIFIER ::= { m3uaAppSpEpAttributes 1}
m3uaRoutingTab OBJECT IDENTIFIER ::= { m3uaTables 4 }
m3uaRtAttributes OBJECT IDENTIFIER ::= { m3uaRoutingTab 1 }
m3uaRtConfig OBJECT IDENTIFIER ::= { m3uaRtAttributes 1 }
m3uaNetworkAppearance OBJECT IDENTIFIER ::= { m3uaTables 5 }
m3uaNaAttributes OBJECT IDENTIFIER ::= { m3uaNetworkAppearance 1}
m3uaNaConfig OBJECT IDENTIFIER ::= { m3uaNaAttributes 1 }
m3uaLookup OBJECT IDENTIFIER ::= { m3uaTables 6 }
-----------------------------------------------------------------------
-- M3UA MANAGEMENT
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIGURATION
-----------------------------------------------------------------------
m3uaVersion OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Identifies the current version of the M3UA."
::= { m3uaConfig 1 }
m3uaProcType OBJECT-TYPE
SYNTAX INTEGER {
sgp(1), -- Signalling Gateway Process
asp(2), -- Application Server Process
ipsp(3) -- IP Server Process
Roque, et al [Page 15]
Internet Draft M3UA MIB using SMIv2 August, 2002
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the type of the process where the
M3UA layer is located."
::= { m3uaConfig 2 }
m3uaLocalPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Identifies the port of the M3UA service.
Well-Known Port for M3UA is 2904."
::= { m3uaConfig 3 }
m3uaTrValue OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Initial value of the Failover timer Tr. Recommended
value is 3000 milliseconds. Tr set with value 0 disables
buffering."
::= { m3uaConfig 4 }
m3uaTPaudValue OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Initial value of the Periodic Audit timer TrPaud.
Recommended value is 5000 milliseconds."
::= { m3uaConfig 5 }
m3uaHeartBeat OBJECT-TYPE
SYNTAX INTEGER {
on(0), -- Heartbeat is enabled.
off(1) -- Heartbeat is disabled. No BEAT msgs
-- sent but BEAT messages received are
-- responded.
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Activates or deactivates the heartbeat procedure at M3UA
level."
Roque, et al [Page 16]
Internet Draft M3UA MIB using SMIv2 August, 2002
::= { m3uaConfig 6 }
m3uaTBeatValue OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Initial value of the HeartBeat timer TBeat. Recommended
value is 1000 milliseconds."
::= { m3uaConfig 7 }
m3uaTAckValue OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Initial value of the Retransmision timer TAck. Recommended
value is 2000 milliseconds."
::= { m3uaConfig 8 }
m3uaSpLshMethod OBJECT-TYPE
SYNTAX INTEGER {
none(0), -- Random
sls(1), -- Basing on SLS
cic(2), -- Basing on CIC
ssn(3), -- Basing on SSN
dpg(4), -- Basing on DPC
other(5) -- Other method
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates the method to be used when the
load must be shared between several ACTIVE Signaling
Processes."
::= { m3uaConfig 9 }
m3uaStreamLshMethod OBJECT-TYPE
SYNTAX INTEGER {
none(0), -- Random
sls(1), -- Basing on SLS
cic(2), -- Basing on CIC
ssn(3), -- Basing on SSN
dpc(4), -- Basing on DPC
other(5) -- Other method
}
MAX-ACCESS read-write
STATUS current
Roque, et al [Page 17]
Internet Draft M3UA MIB using SMIv2 August, 2002
DESCRIPTION
"This variable indicates the method to be used when the
load must be shared between several streams within the same
SCTP Association."
::= { m3uaConfig 10 }
m3uaFailOverBuffSize OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Size of the failover retransmision buffer. Recommended
value is 64 Kbytes. Only valid if failover buffer
option has been set to ON."
::= { m3uaConfig 11 }
-----------------------------------------------------------------------
-- ATTRIBUTES-STATISTICS
-----------------------------------------------------------------------
m3uaRoutingFailures OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times a routing operation against Routing
Table fails. No final SCTP Association ID is obtained from
the routing operation. That is the reason why this is a
general statistic instead a per association statistic."
::= { m3uaStatistics 1 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE LOGICAL APPLICATION TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- The Logical Applications table contains information about each
-- Application for which one or more routing keys can exist in the
-- routing table. Log. Applications are: Signaling Gateways (SGs),
-- Application Servers (ASs).
m3uaAppTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaAppEntry
MAX-ACCESS not-accessible
Roque, et al [Page 18]
Internet Draft M3UA MIB using SMIv2 August, 2002
STATUS current
DESCRIPTION
"A table containing Log. Application-specific information."
::= { m3uaLAppConfig 1 }
m3uaAppEntry OBJECT-TYPE
SYNTAX M3uaAppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for the Log. App."
INDEX { m3uaAppId }
::= { m3uaAppTable 1 }
M3uaAppEntry ::= SEQUENCE {
m3uaAppId Unsigned32,
m3uaAppType INTEGER,
m3uaAppState INTEGER,
m3uaAppTrafficMode INTEGER,
m3uaAppRowStatus RowStatus
}
m3uaAppId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Application Identification Value."
::= { m3uaAppEntry 1 }
m3uaAppType OBJECT-TYPE
SYNTAX INTEGER {
sg(1),
as(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Logical Application Type:
SG: Signaling Gateway.
AS: Application Server.
"
::= { m3uaAppEntry 2 }
m3uaAppState OBJECT-TYPE
SYNTAX INTEGER {
active(1),
inactive(2),
down(3),
pending(4)
}
Roque, et al [Page 19]
Internet Draft M3UA MIB using SMIv2 August, 2002
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current Logical Application State. Based on the state
of the Signaling Processes which serve it."
::= { m3uaAppEntry 3 }
m3uaAppTrafficMode OBJECT-TYPE
SYNTAX INTEGER {
override(1),
loadshare(2),
broadcast(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current Logical Application traffic handling mode."
::= { m3uaAppEntry 4 }
m3uaAppRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaAppEntry 5 }
-----------------------------------------------------------------------
-- ATTRIBUTES-STATISTICS
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE LOGICAL APPLICATION STATISTICS TABLE
-----------------------------------------------------------------------
m3uaAppStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaAppStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing Log. Application statistic information."
::= { m3uaLAppStatistics 1 }
m3uaAppStatEntry OBJECT-TYPE
SYNTAX M3uaAppStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for the Log. App."
INDEX { m3uaAppId } -- SHARED INDEX
Roque, et al [Page 20]
Internet Draft M3UA MIB using SMIv2 August, 2002
::= { m3uaAppStatTable 1 }
M3uaAppStatEntry ::= SEQUENCE {
m3uaAppUnreachable Counter32 }
m3uaAppUnreachable OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times that the Application is unreachable
through any of the Signaling Processes that are serving
it."
::= { m3uaAppStatEntry 1 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE SIGNALING PROCESS ENDPOINT TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- Defines data related to a Signaling Process Endpoint.
-- A SP Endpoint identifies a peer node were a SGP, ASP or IPSP are
-- running.
-- This table exists with any Proccess Type.
-- The table contains the Endpoint Identifier and data related to the
-- SCTP association to that remote endpoint.
-- The Signaling Process Endpoint table contains information about
-- specific data regarding the physical location of that endpoint,
-- the list of remote IP addresses of that endpoint, and the list of
-- local IP addresses that want to be used against that endpoint.
-- This table is expanded with the Remote IP Address Table that
-- identify the endpoint and with the Local IP Address Table that
-- identify the local node for that endpoint.
-- The table contains data related to the Association, as its state,
-- number of streams, and the Association ID, provided by SCTP when
-- the association is established.
m3uaSpEpTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaSpEpEntry
MAX-ACCESS not-accessible
Roque, et al [Page 21]
Internet Draft M3UA MIB using SMIv2 August, 2002
STATUS current
DESCRIPTION
"A table containing Signaling Process Endpoint-specific
information."
::= { m3uaSpEpConfig 1 }
m3uaSpEpEntry OBJECT-TYPE
SYNTAX M3uaSpEpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for the Signaling Process
Endpoint."
INDEX { m3uaSpEpId }
::= { m3uaSpEpTable 1 }
M3uaSpEpEntry ::= SEQUENCE {
m3uaSpEpId Unsigned32,
m3uaSpEpAssocId Unsigned32,
m3uaSpEpAssocRemHostName OCTET STRING,
m3uaSpEpAssocRemPort Unsigned32,
m3uaSpEpAssocReqOutStreams Unsigned32,
m3uaSpEpAssocOutStreams Unsigned32,
m3uaSpEpAssocIncStreams Unsigned32,
m3uaSpEpAssocState INTEGER,
m3uaSpEpRowStatus RowStatus
}
m3uaSpEpId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Signaling Process Endpoint Identification Value."
::= { m3uaSpEpEntry 1 }
m3uaSpEpAssocId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Association Identification. Value identifying the
association for that endpoint. This value is extracted from
the SCTP association Id value returned by SCTP when the
association is established to that endpoint."
::= { m3uaSpEpEntry 2 }
m3uaSpEpAssocRemHostName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..255))
Roque, et al [Page 22]
Internet Draft M3UA MIB using SMIv2 August, 2002
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Peer's DNS name.
If no DNS domain name was received at init time from the
peer, this entry will be meaningless, therefore it will
store a NULL value.
Otherwise, the remote host name received at init time will
be stored."
::= { m3uaSpEpEntry 3 }
m3uaSpEpAssocRemPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"M3UA port number to connect to remote Endpoint."
::= { m3uaSpEpEntry 4 }
m3uaSpEpAssocReqOutStreams OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the SCTP association is initiated from the local peer,
this will be the number of outgoing streams that will be
requested to the remote peer at association start up."
::= { m3uaSpEpEntry 5 }
m3uaSpEpAssocOutStreams OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"outgoing Streams according to the negotiation at
association start up. This parameter has to be read-only by
the manager."
::= { m3uaSpEpEntry 6 }
m3uaSpEpAssocIncStreams OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Incoming Streams according to the negotiation at assoc.
start up. This parameter has to be read-only by the
manager."
::= { m3uaSpEpEntry 7 }
Roque, et al [Page 23]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaSpEpAssocState OBJECT-TYPE
SYNTAX INTEGER {
closed(1),
established(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of this SCTP association."
::= { m3uaSpEpEntry 8 }
m3uaSpEpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaSpEpEntry 9 }
-----------------------------------------------------------------------
-- ATTRIBUTES-STATISTICS
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE SP ENDPOINT STATISTICS TABLE
-----------------------------------------------------------------------
-- Defines statistics related to a Signaling Process Endpoint.
-- This table exists with any Proccess Type.
-- The table contains statistics data related to the M3UA messaging
-- exchanged through that association between the Signaling Processes
-- that hold the association.
m3uaSpEpStatTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaSpEpStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing Signaling Process Endpoint-specific
information."
::= { m3uaSpEpStatistics 1 }
m3uaSpEpStatEntry OBJECT-TYPE
SYNTAX M3uaSpEpStatEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for the SP Endpoint."
Roque, et al [Page 24]
Internet Draft M3UA MIB using SMIv2 August, 2002
INDEX { m3uaSpEpId } -- shared index
::= { m3uaSpEpStatTable 1 }
M3uaSpEpStatEntry ::= SEQUENCE {
m3uaSpEpAssocDataOut Counter32,
m3uaSpEpAssocDataIn Counter32,
m3uaSpEpAssocAspupOut Counter32,
m3uaSpEpAssocAspupAckOut Counter32,
m3uaSpEpAssocAspacOut Counter32,
m3uaSpEpAssocAspacAckOut Counter32,
m3uaSpEpAssocAspdnOut Counter32,
m3uaSpEpAssocAspdnAckOut Counter32,
m3uaSpEpAssocAspiaOut Counter32,
m3uaSpEpAssocAspiaAckOut Counter32,
m3uaSpEpAssocAspupIn Counter32,
m3uaSpEpAssocAspupAckIn Counter32,
m3uaSpEpAssocAspacIn Counter32,
m3uaSpEpAssocAspacAckIn Counter32,
m3uaSpEpAssocAspdnIn Counter32,
m3uaSpEpAssocAspdnAckIn Counter32,
m3uaSpEpAssocAspiaIn Counter32,
m3uaSpEpAssocAspiaAckIn Counter32,
m3uaSpEpAssocNotifyOut Counter32,
m3uaSpEpAssocErrorOut Counter32,
m3uaSpEpAssocNotifyIn Counter32,
m3uaSpEpAssocErrorIn Counter32,
m3uaSpEpAssocDunaOut Counter32,
m3uaSpEpAssocDavaOut Counter32,
m3uaSpEpAssocSconOut Counter32,
m3uaSpEpAssocDupuOut Counter32,
m3uaSpEpAssocDaudOut Counter32,
m3uaSpEpAssocDunaIn Counter32,
m3uaSpEpAssocDavaIn Counter32,
m3uaSpEpAssocSconIn Counter32,
m3uaSpEpAssocDupuIn Counter32,
m3uaSpEpAssocDaudIn Counter32
}
-- Association Statistics
-- DATA Statistics per Association
m3uaSpEpAssocDataOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DATA messages sent through the association."
::= { m3uaSpEpStatEntry 1 }
m3uaSpEpAssocDataIn OBJECT-TYPE
Roque, et al [Page 25]
Internet Draft M3UA MIB using SMIv2 August, 2002
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DATA messages received through the association."
::= { m3uaSpEpStatEntry 2 }
-- End of DATA Statistics per Association
-- ASPM Statistics per Association
m3uaSpEpAssocAspupOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPUP messages sent through the association."
::= { m3uaSpEpStatEntry 3 }
m3uaSpEpAssocAspupAckOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPUP ACK messages sent through the
association."
::= { m3uaSpEpStatEntry 4 }
m3uaSpEpAssocAspacOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPAC messages sent through the association."
::= { m3uaSpEpStatEntry 5 }
m3uaSpEpAssocAspacAckOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPAC ACK messages sent through the
association."
::= { m3uaSpEpStatEntry 6 }
m3uaSpEpAssocAspdnOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPDN messages sent through the association."
Roque, et al [Page 26]
Internet Draft M3UA MIB using SMIv2 August, 2002
::= { m3uaSpEpStatEntry 7 }
m3uaSpEpAssocAspdnAckOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPDN ACK messages sent through the
association."
::= { m3uaSpEpStatEntry 8 }
m3uaSpEpAssocAspiaOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPIA messages sent through the association."
::= { m3uaSpEpStatEntry 9 }
m3uaSpEpAssocAspiaAckOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPIA ACK messages sent through the
association."
::= { m3uaSpEpStatEntry 10 }
m3uaSpEpAssocAspupIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPUP messages received through the
association."
::= { m3uaSpEpStatEntry 11 }
m3uaSpEpAssocAspupAckIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPUP ACK messages received through the
association."
::= { m3uaSpEpStatEntry 12 }
m3uaSpEpAssocAspacIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Roque, et al [Page 27]
Internet Draft M3UA MIB using SMIv2 August, 2002
"Number of ASPAC messages received through the
association."
::= { m3uaSpEpStatEntry 13 }
m3uaSpEpAssocAspacAckIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPAC ACK messages received through the
association."
::= { m3uaSpEpStatEntry 14 }
m3uaSpEpAssocAspdnIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPDN messages received through the
association."
::= { m3uaSpEpStatEntry 15 }
m3uaSpEpAssocAspdnAckIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPDN ACK messages received through the
association."
::= { m3uaSpEpStatEntry 16 }
m3uaSpEpAssocAspiaIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPIA messages received through the
association."
::= { m3uaSpEpStatEntry 17 }
m3uaSpEpAssocAspiaAckIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ASPIA ACK messages received through the
association."
::= { m3uaSpEpStatEntry 18 }
-- End of ASPM Statistics per Association
Roque, et al [Page 28]
Internet Draft M3UA MIB using SMIv2 August, 2002
-- MGMT Statistics per Association
m3uaSpEpAssocNotifyOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of NOTIFY messages sent through the association."
::= { m3uaSpEpStatEntry 19 }
m3uaSpEpAssocErrorOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ERROR messages sent through the association."
::= { m3uaSpEpStatEntry 20 }
m3uaSpEpAssocNotifyIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of NOTIFY messages received through the
association."
::= { m3uaSpEpStatEntry 21 }
m3uaSpEpAssocErrorIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ERROR messages received through the association."
::= { m3uaSpEpStatEntry 22 }
-- End of MGMT Statistics per Association
-- SSNM Statistics per Association
m3uaSpEpAssocDunaOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DUNA messages sent through the association."
::= { m3uaSpEpStatEntry 23 }
m3uaSpEpAssocDavaOut OBJECT-TYPE
SYNTAX Counter32
Roque, et al [Page 29]
Internet Draft M3UA MIB using SMIv2 August, 2002
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DAVA messages sent through the association."
::= { m3uaSpEpStatEntry 24 }
m3uaSpEpAssocSconOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of SCON messages sent through the association."
::= { m3uaSpEpStatEntry 25 }
m3uaSpEpAssocDupuOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DUPU messages sent through the association."
::= { m3uaSpEpStatEntry 26 }
m3uaSpEpAssocDaudOut OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DAUD messages sent through the association."
::= { m3uaSpEpStatEntry 27 }
m3uaSpEpAssocDunaIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DUNA messages received through the association."
::= { m3uaSpEpStatEntry 28 }
m3uaSpEpAssocDavaIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DAVA messages received through the association."
::= { m3uaSpEpStatEntry 29 }
m3uaSpEpAssocSconIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Roque, et al [Page 30]
Internet Draft M3UA MIB using SMIv2 August, 2002
"Number of SCON messages received through the association."
::= { m3uaSpEpStatEntry 30 }
m3uaSpEpAssocDupuIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DUPU messages received through the association."
::= { m3uaSpEpStatEntry 31 }
m3uaSpEpAssocDaudIn OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of DAUD messages received through the association."
::= { m3uaSpEpStatEntry 32 }
-- End of SSNM Statistics per Association
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE APPLICATION-ENDPOINT TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- The Application-Endpoint table contains information about the
-- Applications that the indexed Endpoint is serving and the state of
-- that endpoint for that specific application.
-- Although an SP is identified with an unique SCTP endpoint, there may
-- be more than one SP table entry indexed by the same SP Endpoint Id.
-- The reason for this is that an Endpoint can be serving several
-- Applications and thus maintains different states for each of them.
-- An entry will then exist in the table per every combination of
-- m3uaSpEpId and m3uaAppId.
m3uaAppSpEpTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaAppSpEpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing Signaling Process Endpoint-specific
information."
::= { m3uaSpEpConfig 2 }
Roque, et al [Page 31]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaAppSpEpEntry OBJECT-TYPE
SYNTAX M3uaAppSpEpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for the SP Endpoint."
INDEX { m3uaSpEpId, -- shared index
m3uaAppId } -- shared index
::= { m3uaAppSpEpTable 1 }
M3uaAppSpEpEntry ::= SEQUENCE {
m3uaAppSpEpState INTEGER,
m3uaAppSpEpRowStatus RowStatus
}
m3uaAppSpEpState OBJECT-TYPE
SYNTAX INTEGER {
active(1),
inactive(2),
down(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current state of the Endpoint for an specific Application.
Based on ASPM Messages."
::= { m3uaAppSpEpEntry 1 }
m3uaAppSpEpRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaAppSpEpEntry 2 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- LOCAL AND REMOTE IP ADDRESS TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- Remote Addresses Table
-----------------------------------------------------------------------
Roque, et al [Page 32]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaAssocLocalAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaAssocLocalAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Expanded table of m3uaAssocTable based on the AssocId
index.
It shows several interesting data for each local
address which takes part in this association."
::= { m3uaSpEpConfig 3 }
m3uaAssocLocalAddressEntry OBJECT-TYPE
SYNTAX M3uaAssocLocalAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Local information about the available addresses."
INDEX { m3uaSpEpId, -- shared index
m3uaAssocLocalAddressIPType,
m3uaAssocLocalAddressIP }
::= { m3uaAssocLocalAddressTable 1 }
M3uaAssocLocalAddressEntry ::= SEQUENCE {
m3uaAssocLocalAddressIPType InetAddressType,
m3uaAssocLocalAddressIP InetAddress,
m3uaAssocLocalAddressRowStatus RowStatus
}
m3uaAssocLocalAddressIPType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of a local IP address available for this
association.
unknown (0) An unknown address type. This value MUST be used
to indicate an IP address different from IPv4 or IPv6. This
value is used in this MIB for error conditions.
ipv4 (1): An IPv4 address as defined by the InetAddressIPv4
textual convention [RFC2851].
ipv6 (2): An IPv6 address as defined by the InetAddressIPv6
textual convention [RFC2851]. It represents global IPv6
addresses and non-global IPv6 addresses in case where no
zone index is needed.
ipv4z(3): A non-global IPv4 address including a zone index
as defined by the InetAddressIPv4z textual convention
Roque, et al [Page 33]
Internet Draft M3UA MIB using SMIv2 August, 2002
[RFC2851].
ipv6z(4): A non-global IPv6 address including a zone index
as defined by the InetAddressIPv6z textual convention
[RFC2851].ö
::= { m3uaAssocLocalAddressEntry 1 }
m3uaAssocLocalAddressIP OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a local IP address available for this
association. An InetAddress value is always interpreted
within the context of an InetAddressType value."
::= { m3uaAssocLocalAddressEntry 2 }
m3uaAssocLocalAddressRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted using the RowStatus convention.
A row in this table will be created per local IP address to
be used in this association. The creation takes part when a
new row in the m3uaAssocTable is created or when a new
IPaddress is added in the local interface (if this function
is allowed).
A row in this table will be deleted per local IP address
used in this association when the corresponding row in
m3uaAssocTable is deleted or when an IP address is removed
from the local interface (if this function is allowed)."
::= { m3uaAssocLocalAddressEntry 3 }
-----------------------------------------------------------------------
-- Remote Addresses Table
-----------------------------------------------------------------------
m3uaAssocRemAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaAssocRemAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Expanded table of m3uaAssocTable based on the AssocId
index.
It shows several interesting data for each remote peer IP
address which is used in this association."
Roque, et al [Page 34]
Internet Draft M3UA MIB using SMIv2 August, 2002
::= { m3uaSpEpConfig 4 }
m3uaAssocRemAddressEntry OBJECT-TYPE
SYNTAX M3uaAssocRemAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about the remote IP address most important
variables"
INDEX { m3uaSpEpId, -- shared index
m3uaAssocRemAddressIPType,
m3uaAssocRemAddressIP }
::= { m3uaAssocRemAddressTable 1 }
M3uaAssocRemAddressEntry ::= SEQUENCE {
m3uaAssocRemAddressIPType InetAddressType,
m3uaAssocRemAddressIP InetAddress,
m3uaAssocRemAddressRowStatus RowStatus
}
m3uaAssocRemAddressIPType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of a local IP address available for this
association.
unknown (0) An unknown address type. This value MUST be used
to indicate an IP address different from IPv4 or IPv6. This
value is used in this MIB for error conditions.
ipv4 (1): An IPv4 address as defined by the InetAddressIPv4
textual convention [RFC2851].
ipv6 (2): An IPv6 address as defined by the InetAddressIPv6
textual convention [RFC2851]. It represents global IPv6
addresses and non-global IPv6 addresses in case where no
zone index is needed.
ipv4z(3): A non-global IPv4 address including a zone index
as defined by the InetAddressIPv4z textual convention
[RFC2851].
ipv6z(4): A non-global IPv6 address including a zone index
as defined by the InetAddressIPv6z textual convention
[RFC2851].ö
::= { m3uaAssocRemAddressEntry 1 }
m3uaAssocRemAddressIP OBJECT-TYPE
Roque, et al [Page 35]
Internet Draft M3UA MIB using SMIv2 August, 2002
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of a local IP address available for this
association. An InetAddress value is always interpreted
within the context of an InetAddressType value."
::= { m3uaAssocRemAddressEntry 2 }
m3uaAssocRemAddressRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted using the RowStatus convention.
A row in this table will be created per local IP address to
be used in this association. The creation takes part when a
new row in the m3uaAssocTable is created or when a new
IPaddress is added in the local interface (if this function
is allowed).
A row in this table will be deleted per local IP address
Used in this association when the corresponding row in
m3uaAssocTable is deleted or when an IP address is removed
from the local interface (if this function is allowed)."
::= { m3uaAssocRemAddressEntry 3 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE ROUTING TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- The Routing table contains a list of routing keys which translate to
-- a Logical Application ID. As stated former in this document,
-- Application Servers and Signaling Gateways are Logical Applications.
-- As a Routing Key may be composed of any combination of basic SS7
-- routing elements, if an element is not included in the routing key,
-- a default value is assigned. This default value can continue being
-- considered as an indexing value itself.
m3uaRoutingTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaRoutingEntry
Roque, et al [Page 36]
Internet Draft M3UA MIB using SMIv2 August, 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing Routing-specific information."
::= { m3uaRtConfig 1 }
m3uaRoutingEntry OBJECT-TYPE
SYNTAX M3uaRoutingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for a Routing Key."
INDEX { m3uaRKId }
::= { m3uaRoutingTable 1 }
M3uaRoutingEntry ::= SEQUENCE {
m3uaRKId Unsigned32,
m3uaRKDpc Unsigned32,
m3uaRKNa Unsigned32,
m3uaPeerAppId Unsigned32,
m3uaPeerAppTrafficMode INTEGER,
m3uaRoutingRowStatus RowStatus
}
m3uaRKId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Local identifier for the routing key."
::= { m3uaRoutingEntry 1 }
m3uaRKDpc OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Destination Point Code for that routing key. A default
value will be assigned if not present in the Routing Key.
Range: 0 - 16777215."
::= { m3uaRoutingEntry 2 }
m3uaRKNa OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Network Appearance for that routing key. A default value
will be assigned if not present in the Routing Key."
::= { m3uaRoutingEntry 3 }
Roque, et al [Page 37]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaPeerAppId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Peer Application Identification Value. It can identify
an Application Server or a Signaling Gateway."
::= { m3uaRoutingEntry 4 }
m3uaPeerAppTrafficMode OBJECT-TYPE
SYNTAX INTEGER {
override(1),
loadshare(2),
broadcast(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Peer Application Traffic Mode Type. Identifies the traffic
mode of operation of SPs within the Peer Application."
::= { m3uaRoutingEntry 5 }
m3uaRoutingRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaRoutingEntry 6 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE SI TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- This table contains a list of SIs that identify the Services covered
-- by that Routing Key. This list is related to and extends information
-- of every entry in Routing Table.
m3uaRKSiTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaRKSiEntry
MAX-ACCESS not-accessible
Roque, et al [Page 38]
Internet Draft M3UA MIB using SMIv2 August, 2002
STATUS current
DESCRIPTION
"A table containing the list of SIs that identify the
services covered by that Routing Key."
::= { m3uaRtConfig 2 }
m3uaRKSiEntry OBJECT-TYPE
SYNTAX M3uaRKSiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaRKId } -- shared index
::= { m3uaRKSiTable 1 }
M3uaRKSiEntry ::= SEQUENCE {
m3uaRKSi Unsigned32,
m3uaRKSiRowStatus RowStatus
}
m3uaRKSi OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Service Indicator for that routing key. A default value
will be assigned if not present in the Routing Key.
Range: 2 - 10."
::= { m3uaRKSiEntry 1 }
m3uaRKSiRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaRKSiEntry 2 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE OPC TABLE
-----------------------------------------------------------------------
Roque, et al [Page 39]
Internet Draft M3UA MIB using SMIv2 August, 2002
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- This table contains a list of OPCs that identify the Originating
-- Node in the SS7 Network. This list is related with and extends
-- information of every entry in Routing Table.
m3uaRKOpcTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaRKOpcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing the list of Point Codes that identify
the Originating Node in the SS7 Network for a Routing
Key."
::= { m3uaRtConfig 3 }
m3uaRKOpcEntry OBJECT-TYPE
SYNTAX M3uaRKOpcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaRKId } -- shared index
::= { m3uaRKOpcTable 1 }
M3uaRKOpcEntry ::= SEQUENCE {
m3uaRKOpc Unsigned32,
m3uaRKOpcRowStatus RowStatus
}
m3uaRKOpc OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Origination Point Code for that routing key. A default
value will be assigned if not present in the Routing Key.
Range: 0 to 16777215."
::= { m3uaRKOpcEntry 1 }
m3uaRKOpcRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
Roque, et al [Page 40]
Internet Draft M3UA MIB using SMIv2 August, 2002
convention."
::= { m3uaRKOpcEntry 2 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE CIC RANGE TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- This table contains a CIC Range for an OPC in the Routing Key
-- This list is related with and extends information
-- of every entry in Routing Table.
m3uaRKCicRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaRKCicRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing the list of CIC Ranges for an OPC
within the specific Routing Key."
::= { m3uaRtConfig 4 }
m3uaRKCicRangeEntry OBJECT-TYPE
SYNTAX M3uaRKCicRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaRKId, -- shared index
m3uaRKOpc }
::= { m3uaRKCicRangeTable 1 }
M3uaRKCicRangeEntry ::= SEQUENCE {
m3uaRKCicMin Unsigned32,
m3uaRKCicMax Unsigned32,
m3uaRKCicRowStatus RowStatus
}
m3uaRKCicMin OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Roque, et al [Page 41]
Internet Draft M3UA MIB using SMIv2 August, 2002
"Minumum value of the Circuit Identification Code
Range for that routing key. A default value will
be assigned if not present in the Routing Key.
Range: 0 to 65535."
::= { m3uaRKCicRangeEntry 1 }
m3uaRKCicMax OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum value of the Circuit Identification Code
Range for that routing key. A default value will
be assigned if not present in the Routing Key.
Range: 0 to 65535."
::= { m3uaRKCicRangeEntry 2 }
m3uaRKCicRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaRKCicRangeEntry 3 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE NETWORK APPEARANCE TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- The NA table contains information about the specific variables
-- that apply to every Network Appearance.
m3uaNaTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaNaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing Network Appearance-specific information"
Roque, et al [Page 42]
Internet Draft M3UA MIB using SMIv2 August, 2002
::= { m3uaNaConfig 1 }
m3uaNaEntry OBJECT-TYPE
SYNTAX M3uaNaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"General common variables for a Network Appearance."
INDEX { m3uaRKNa } -- shared index
::= { m3uaNaTable 1 }
M3uaNaEntry ::= SEQUENCE {
m3uaNaNI Unsigned32,
m3uaNaMtp3ProtocolType INTEGER,
m3uaNaMtp3ProtocolVariant Unsigned32,
m3uaNaMtp3ProtocolVersion Unsigned32,
m3uaNaRowStatus RowStatus
}
m3uaNaNI OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Identifies the Network Indicator of the SG Node in the
SS7 Network."
::= { m3uaNaEntry 2 }
m3uaNaMtp3ProtocolType OBJECT-TYPE
SYNTAX INTEGER {
itu(1),
ansi(2),
china(3),
ttc(4),
other(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The MTP3 protocol type for this NA."
::= { m3uaNaEntry 4 }
m3uaNaMtp3ProtocolVariant OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Roque, et al [Page 43]
Internet Draft M3UA MIB using SMIv2 August, 2002
"The MTP3 protocol variant for this NA."
::= { m3uaNaEntry 5 }
m3uaNaMtp3ProtocolVersion OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The MTP3 protocol version for this NA."
::= { m3uaNaEntry 6 }
m3uaNaRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaNaEntry 7 }
-----------------------------------------------------------------------
-- M3UA TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- THE POINT CODE TABLE
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ATTRIBUTES - CONFIG
-----------------------------------------------------------------------
-- The PC table contains a list of point codes that identify the SG
-- node in the SS7 Network. This list is related with and extends
-- information of every NA in NA Table.
-- This table expand information in entries in Network Appearance
-- Table. A SG with several Network Appearances may be connected to
-- different SS7 Networks and may be represented in each SS7 Network by
-- different Point Codes.
m3uaNaPcTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaNaPcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Roque, et al [Page 44]
Internet Draft M3UA MIB using SMIv2 August, 2002
"A table containing the list of Point Codes that identify
the SG Node in the SS7 Network for that Network App."
::= { m3uaNaConfig 2 }
m3uaNaPcEntry OBJECT-TYPE
SYNTAX M3uaNaPcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaRKNa, -- shared index
m3uaNaPC }
::= { m3uaNaPcTable 1 }
M3uaNaPcEntry ::= SEQUENCE {
m3uaNaPC Unsigned32,
m3uaNaPcRowStatus RowStatus
}
m3uaNaPC OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Point Code Value. Range: 0 to 16777215."
::= { m3uaNaPcEntry 1 }
m3uaNaPcRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted by management operation using the RowStatus
convention."
::= { m3uaNaPcEntry 2 }
-----------------------------------------------------------------------
-- M3UA LOOKUP REVERSE TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ENDPOINT BY ASSOCIATION
-----------------------------------------------------------------------
-- This table allows the obtention of the Remote Endpoint Local Id
-- for an specific association.
Roque, et al [Page 45]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaLookupSpEpbyAssocTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaLookupSpEpbyAssocEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing the list of remote Endpoints defined
indexed by the Id of the association established to that
Endpoint."
::= { m3uaLookup 1 }
m3uaLookupSpEpbyAssocEntry OBJECT-TYPE
SYNTAX M3uaLookupSpEpbyAssocEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaSpEpAssocId, -- shared index
m3uaLookupSpEpId } -- shared index
::= { m3uaLookupSpEpbyAssocTable 1 }
M3uaLookupSpEpbyAssocEntry ::= SEQUENCE {
m3uaLookupSpEpId Unsigned32
}
m3uaLookupSpEpId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Signaling Process Endpoint Identification Value."
::= { m3uaLookupSpEpbyAssocEntry 1 }
-----------------------------------------------------------------------
-- M3UA LOOKUP REVERSE TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ROUTING KEYS BY APPLICATION ID
-----------------------------------------------------------------------
-- This table allows the obtention of the Routing Keys for an specific
-- Application.
m3uaLookupRkbyAppTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaLookupRkbyAppEntry
MAX-ACCESS not-accessible
STATUS current
Roque, et al [Page 46]
Internet Draft M3UA MIB using SMIv2 August, 2002
DESCRIPTION
"A table containing the list of Routing Keys defined
for an Application."
::= { m3uaLookup 2 }
m3uaLookupRkbyAppEntry OBJECT-TYPE
SYNTAX M3uaLookupRkbyAppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaPeerAppId, -- shared index
m3uaLookupRKId } -- shared index
::= { m3uaLookupRkbyAppTable 1 }
M3uaLookupRkbyAppEntry ::= SEQUENCE {
m3uaLookupRKId Unsigned32
}
m3uaLookupRKId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Routing Key Identification Value."
::= { m3uaLookupRkbyAppEntry 1 }
-----------------------------------------------------------------------
-- M3UA LOOKUP REVERSE TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ROUTING KEYS BY DPC-NA
-----------------------------------------------------------------------
-- This table allows the obtention of the Routing Key for an specific
-- DPC-NA combination.
m3uaLookupRkbyDpcNaTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaLookupRkbyDpcNaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing the list of Routing Keys defined
for an Application."
::= { m3uaLookup 3 }
m3uaLookupRkbyDpcNaEntry OBJECT-TYPE
SYNTAX M3uaLookupRkbyDpcNaEntry
Roque, et al [Page 47]
Internet Draft M3UA MIB using SMIv2 August, 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaRKDpc, -- shared index
m3uaRKNa, -- shared index
m3uaRKId } -- shared index
::= { m3uaLookupRkbyDpcNaTable 1 }
M3uaLookupRkbyDpcNaEntry ::= SEQUENCE {
m3uaLookupRKbyDpcNaId Unsigned32
}
m3uaLookupRKbyDpcNaId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Routing Key Identification Value."
::= { m3uaLookupRkbyDpcNaEntry 1 }
-----------------------------------------------------------------------
-- M3UA LOOKUP REVERSE TABLES
-----------------------------------------------------------------------
-----------------------------------------------------------------------
-- ENDPOINTS BY APPLICATION ID
-----------------------------------------------------------------------
-- This table allows the obtention of the Endpoints serving an specific
-- Application.
m3uaLookupSpEpbyAppTable OBJECT-TYPE
SYNTAX SEQUENCE OF M3uaLookupSpEpbyAppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing the list of Endpoints Id serving
an Application."
::= { m3uaLookup 4 }
m3uaLookupSpEpbyAppEntry OBJECT-TYPE
SYNTAX M3uaLookupSpEpbyAppEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Point Code Entry."
INDEX { m3uaAppId, -- shared index
m3uaLookupSpEpbyAppId } -- shared index
::= { m3uaLookupSpEpbyAppTable 1 }
Roque, et al [Page 48]
Internet Draft M3UA MIB using SMIv2 August, 2002
M3uaLookupSpEpbyAppEntry ::= SEQUENCE {
m3uaLookupSpEpbyAppId Unsigned32
}
m3uaLookupSpEpbyAppId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Signaling Process Endpoint Identification Value."
::= { m3uaLookupSpEpbyAppEntry 1 }
-- 4.1 Conformance Information
m3uaGroups OBJECT IDENTIFIER ::= { m3uaConformance 1 }
m3uaCompliances OBJECT IDENTIFIER ::= { m3uaConformance 2 }
-- 4.1.1 Compliance Statements
m3uaCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMPv3 entities which
implement M3UA.
The M3UA MIB specifies in this compliant implementation that
Only need to support IPv4/IPv6 addresses without a zone index,
unknown type and DNS names. Support for IPv4/IPv6 addresses
without zone indices is not required."
MODULE -- this module
MANDATORY-GROUPS { m3uaAttributesGroup,
m3uaLogAppAttributesTableGroup,
m3uaSpEpAttributesTableGroup,
m3uaAppSpEpAttributesTableGroup,
m3uaRoutingAttributesTableGroup,
m3uaRKSiAttributesTableGroup,
m3uaRKOpcAttributesTableGroup,
m3uaRKCicRangeAttribTableGroup,
m3uaNaAttributesTableGroup,
m3uaPcAttributesTableGroup,
m3uaLocAddrAttributesTableGroup,
m3uaRemAddrAttributesTableGroup
}
OBJECT m3uaAssocLocalAddressIPType
SYNTAX InetAddressType {unknown(0), ipv4(1), ipv6(2) }
Roque, et al [Page 49]
Internet Draft M3UA MIB using SMIv2 August, 2002
DESCRIPTION
"It is only required to have IPv4 and IPv6 addresses
without zone indices. Unknown values must also be
supported in case the IP address has an invalid/unknown
format."
OBJECT m3uaAssocRemAddressIPType
SYNTAX InetAddressType {unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"It is only required to have IPv4 and IPv6 addresses
without zone indices. Unknown values must also be
supported in case the IP address has an invalid/unknown
format."
::= { m3uaCompliances 1 }
-- 4.1.2 Units of conformance
m3uaAttributesGroup OBJECT-GROUP
OBJECTS { m3uaVersion,
m3uaProcType,
m3uaLocalPort,
m3uaTrValue,
m3uaTBeatValue,
m3uaTAckValue,
m3uaTPaudValue,
m3uaHeartBeat,
m3uaSpLshMethod,
m3uaStreamLshMethod,
m3uaFailOverBuffSize,
m3uaRoutingFailures
}
STATUS current
DESCRIPTION
"The m3ua group of objects providing for management of M3UA
entities. Common parameters for the protocol."
::= { m3uaGroups 1 }
m3uaLogAppAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaAppId,
m3uaAppType,
m3uaAppState,
m3uaAppTrafficMode,
m3uaAppUnreachable
}
STATUS current
DESCRIPTION
"The m3ua group of objects to manage ASs/SGs and IPSs."
::= { m3uaGroups 2 }
m3uaSpEpAttributesTableGroup OBJECT-GROUP
Roque, et al [Page 50]
Internet Draft M3UA MIB using SMIv2 August, 2002
OBJECTS { m3uaSpEpId,
m3uaSpEpAssocId,
m3uaSpEpAssocRemHostName,
m3uaSpEpAssocRemPort,
m3uaSpEpAssocReqOutStreams,
m3uaSpEpAssocOutStreams,
m3uaSpEpAssocIncStreams,
m3uaSpEpAssocState,
m3uaSpEpAssocState,
m3uaSpEpAssocDataOut,
m3uaSpEpAssocDataIn,
m3uaSpEpAssocAspupOut,
m3uaSpEpAssocAspupAckOut,
m3uaSpEpAssocAspacOut,
m3uaSpEpAssocAspacAckOut,
m3uaSpEpAssocAspdnOut,
m3uaSpEpAssocAspdnAckOut,
m3uaSpEpAssocAspiaOut,
m3uaSpEpAssocAspiaAckOut,
m3uaSpEpAssocAspupIn,
m3uaSpEpAssocAspupAckIn,
m3uaSpEpAssocAspacIn,
m3uaSpEpAssocAspacAckIn,
m3uaSpEpAssocAspdnIn,
m3uaSpEpAssocAspdnAckIn,
m3uaSpEpAssocAspiaIn,
m3uaSpEpAssocAspiaAckIn,
m3uaSpEpAssocNotifyOut,
m3uaSpEpAssocErrorOut,
m3uaSpEpAssocNotifyIn,
m3uaSpEpAssocErrorIn,
m3uaSpEpAssocDunaOut,
m3uaSpEpAssocDavaOut,
m3uaSpEpAssocSconOut,
m3uaSpEpAssocDupuOut,
m3uaSpEpAssocDaudOut,
m3uaSpEpAssocDunaIn,
m3uaSpEpAssocDavaIn,
m3uaSpEpAssocSconIn,
m3uaSpEpAssocDupuIn,
m3uaSpEpAssocDaudIn
}
STATUS current
DESCRIPTION
"The m3ua group of objects to manage SP Endpoints."
::= { m3uaGroups 3 }
m3uaAppSpEpAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaAppSpEpState
}
Roque, et al [Page 51]
Internet Draft M3UA MIB using SMIv2 August, 2002
STATUS current
DESCRIPTION
"The m3ua group of objects to manage Signaling Processes
(SGPs, ASPs or IPSPs) for the different Applications
they are serving."
::= { m3uaGroups 4 }
m3uaRoutingAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaRKId,
m3uaRKDpc,
m3uaRKNa,
m3uaPeerAppId,
m3uaPeerAppTrafficMode
}
STATUS current
DESCRIPTION
"The m3ua group of objects to manage Routing Tables."
::= { m3uaGroups 5 }
m3uaRKSiAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaRKSi }
STATUS current
DESCRIPTION
"The m3ua group of objects to manage SI Table for a RKey."
::= { m3uaGroups 6 }
m3uaRKOpcAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaRKOpc }
STATUS current
DESCRIPTION
"The m3ua group of objects to manage OPC Table for a RKey."
::= { m3uaGroups 7 }
m3uaRKCicRangeAttribTableGroup OBJECT-GROUP
OBJECTS { m3uaRKCicMin,
m3uaRKCicMax }
STATUS current
DESCRIPTION
"The m3ua group of objects to manage CIC Table for a RKey."
::= { m3uaGroups 8 }
m3uaNaAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaNaNI,
m3uaNaMtp3ProtocolType,
m3uaNaMtp3ProtocolVariant,
m3uaNaMtp3ProtocolVersion
}
Roque, et al [Page 52]
Internet Draft M3UA MIB using SMIv2 August, 2002
STATUS current
DESCRIPTION
"The m3ua group of objects to manage NA Tables."
::= { m3uaGroups 9 }
m3uaPcAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaNaPC
}
STATUS current
DESCRIPTION
"The m3ua group of objects to manage PC Tables."
::= { m3uaGroups 10 }
m3uaLocAddrAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaAssocLocalAddressIPType,
m3uaAssocLocalAddressIP
}
STATUS current
DESCRIPTION
"The m3ua group of objects to manage Local IP Add. Tables."
::= { m3uaGroups 11 }
m3uaRemAddrAttributesTableGroup OBJECT-GROUP
OBJECTS { m3uaAssocRemAddressIPType,
m3uaAssocRemAddressIP
}
STATUS current
DESCRIPTION
"The m3ua group of objects to manage Remote IP Add.
Tables."
::= { m3uaGroups 12 }
END
5. References
[M3UA] G. Sidebottom, L. Ong, Guy Mousseau, K. Gradischnig, H. J.
Schwarzbauer, K. Morneault, I. Rytina, M. Kalla, N. Glaude,
"SS7 MTP3-User Adaptation Layer (M3UA)",
Internet Draft <draft-ietf-sigtran-m3ua-11.txt>,
January 2002.
[MIBMPLS] Cucchiara et al. "Definnitions of Managed Objects for the
Multiprotocol Label Switching, Label Distribution Protocol
(LDP)", Internet Draf <draft-ietf-mpls-ldp-mib-04.txt>,
January 2000.
[SecSNMP] Stallings, W., "SNMP3: A Security Enhancement for SNMP",
Roque, et al [Page 53]
Internet Draft M3UA MIB using SMIv2 August, 2002
IEEE Communication Surveys, Forth quarter 1998, Vol. 1
No. 1.
[Cong] Jacobson, V., "Congestion Avoidance and Control", SIGCOMM
1988, Stanford, California.
[RFC2571] Harrington, D., Presuhn, R.,and B. Wijnen, "An Architecture
for Describing SNMP Management Frameworks", RFC 2571, April
1999.
[RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991.
[RFC1215] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen,
"Message Processing and Dispatching for the Simple Network
Management Protocol (SNMP)", RFC 2572, April 1999.
[RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999.
[RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Roque, et al [Page 54]
Internet Draft M3UA MIB using SMIv2 August, 2002
Management Protocol (SNMPv2)", RFC 1905, January 1996.
[RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications",
RFC 2573, April 1999.
[RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction to Version 3 of the Internet-standard Network
Management Framework", RFC 2570, April 1999.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, Harvard University,
March 1997
[RFC2851-update] Textual Conventions for Internet Network Addresses,
draft-ietf-ops-rfc2851-update-04.txt, Septemeber 20, 2001.
Work in progress.
[RFC2786] R. Frye,D. Levi ,S. Routhier, B. Wijnen , " Coexistence
between Version 1, Version 2, and Version 3 of the Internet
standard Network Management Framework ", draft-ietf-ops-
rfc2851-update-06.txt, DEcember 2000.
[TADRESS] Textual Conventions for Transport Addresses,
draft-ietf-ops-taddress-mib-01.txt, Septemeber 20, 2001.
Work in progress.
6. Security Consideration
There are a number of management objects defined in this MIB that have a
MAX-ACCESS clause of read-write and/or read-create. Such objects may be
considered sensitive or vulnerable in some network environments. The
support for SET operations in a non-secure environment without proper
protection can have a negative effect on network operations.
It is thus important to control even GET access to these objects and
possibly to even encrypt the values of these object when sending them
over the network via SNMP. Not all versions of SNMP provide features for
such a secure environment.
SNMPv1 by itself is not a secure environment. Even if security measures
are taken (e.g., using IPSEC), there is no per-user control as to who
(once an IPSEC association is established between hosts) is allowed to
GET or SET the objects in this MIB
It is recommended that the implementers consider the security features as
provided by the SNMPv3 framework. Specifically, the use of the User-
Roque, et al [Page 55]
Internet Draft M3UA MIB using SMIv2 August, 2002
based Security Model RFC 2574 [RFC2574] and the View-based Access Control
Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP entity
giving access to an instance of this MIB, is properly configured to give
access to the objects only to those principals (users) that have
legitimate rights to indeed GET or SET (change/create/delete) them.
7. Acknowledgments
The author wish to thank Shyamal Prasad, Kurt Kite, Jennifer Jones,
Srivats P., Ken Morneault and Javier Pastor for their comments.
8. Authors' Addresses
Antonio Roque Tel: +34-91-339-3523
Ericsson Espana S.A. EMail: Antonio.Roque@ericsson.com
Network Communication Services
Omb” 3, 4th floor
Madrid, 28045
Spain
9. Revision History
9.1 Changes from draft rev 03 to draft rev 04:
o Integer32 is imported but not used. Removed
o TEXTUAL-CONVENTION is imported but not used. Removed
o mib-2 suggested as branch for mib
o m3uaAppSpEpState consistently defined as INTEGER
o m3uaPeerAppTrafficMode consistently defined as INTEGER
o Fixed error in m3uaSpEpEntry object description text
o Rework in m3uaAppType object description text
9.2 Changes from draft rev 02 to draft rev 03:
o Value range of m3uaAppTrafficMode object is modified.
o Object m3uaLocalPort is changed to "read-write". A comment
is added with the recommended IANA port number.
Roque, et al [Page 56]
Internet Draft M3UA MIB using SMIv2 August, 2002
o Object m3uaFailOverBuffering is deleted. A comment in object
m3uaTrValue is added: If Tr is 0 then FailOver Buffering is Off.
Thus, there is no further need for this element.
o Object m3uaMaxPeerApplications is deleted.
o Object m3uaMaxSPperApplications is deleted.
o Object m3uaAppType is added to Logical Application Table.
o Replace "Sent" by "out" and "Received" by "in" in statistics.
o Object m3uaSSN is deleted from Routing Table
o Object m3uaNI is deleted from Routing Table
o Object m3uaPeerAppTrafficMode is added to Routing Table
o Index m3uaAppId in SP Endpoint Statistic Table is removed
o Signaling Process Table replaced by Application-Endpoint Table
o Index m3uaSpEpAssocId in SP Endpoint Table is removed
o Index m3uaSpEpassocId in Local and Remote IP address table is
replaced by m3uaSpEpId.
o Added new Lookup Reverse Tables for:
- Get EndPoint Id from Association Id.
- Get Routing Key Id from Application Id.
- Get Routing Key Id from DPC and NA.
- Get Endpoints serving an Application.
o Routing Table has been reestructured to deal with multiplicity
of SIs, OPCs and CIC Ranges per Routing Key.
Three new subtables are used.
9.3 Changes from draft rev 01 to draft rev 02:
o Section 3.1.2.3 Signaling Process Table - Chapter re-phrased
o Section 3.1.2.4 Signaling Process Endpoint Table - Last paragraph
removed
o Section 3.1.2.5 Signaling Process Endpoint Statistics Table
m3uaAppId and m3uaSpEpId added to the table figure
Corresponding changes in Definitions chapter applied.
o Section 3.1.2.6 Network Appearance Table
Fixed Duplicate Section No.
Roque, et al [Page 57]
Internet Draft M3UA MIB using SMIv2 August, 2002
m3uaNaRowStatus added to table figure.
Corresponding changes in Definitions chapter applied.
o Object definition of m3uaMaxStreamInbound is removed.
o Object Definition of m3uaSpEpEntry
Index "m3uaAppId" is replaced by m3uaSpEpAssocId.
o Object Definition of m3uaSpEpStatRowStatus
Definition is deleted.
9.4 Changes due to the alignment with the RFC2851 update.
o Include clarification text of the IP address types supported in the
M3UA MIB. Chapter 3.1.2.7.2 (Local and Remote IP address table)
o Remote Primary IP address: Addition of the ipv4z an ipv6z types for
non-globally IP addresses in which a scope identifier is needed.
Addition of the scope of ipv6 type. All of them according to the
RFC2851update-v04
o InetAddressType for local and remote IP addresses:
Limit UNKNOWN type only for unknown IP address format. Remove UNKNOWN
type for zero-length value in the InetAddress since it will be never
zero-length due to the size restriction (0..64)
Addition of the ipv4z an ipv6z types for non-globally IP addresses in
which a scope identifier is needed. Addition of the scope of ipv6 type.
All of them according to the RFC2851update-v04
o Conformance:
Description: Specify that the M3UA MIB only need to support IPv4/IPv6
addresses without a zone index, unknown type and DNS names. Support for
IPv4/IPv6 addresses without zone indices is not required.
InetAddressType of local and remote IP address: Clarify the
implementation is only required to support IPv4 and IPv6 address types
without zone indices. Clarify also that UNKONWN type is only used in
case of lcoal and remote addresses when invalid/unknown IP address
format
Roque, et al [Page 58]
|
Documentation